Bucyrus BSL Maintenance Procedures Technical Manual BI616269
Bucyrus BSL Maintenance Procedures Technical Manual BI616269 - Image 2
Bucyrus BSL Maintenance Procedures Technical Manual BI616269 - Image 3
Bucyrus BSL Maintenance Procedures Technical Manual BI616269 - Image 4
Bucyrus BSL Maintenance Procedures Technical Manual BI616269 - Image 5

Bucyrus BSL Maintenance Procedures Technical Manual BI616269

$30.00

  • Type Of Manual: Technical Manual
  • Manual ID: BI616269
  • Number of Pages: 10
  • Size: 0.9MB
  • Format: PDF
Category:

Product details

  • Model List:

    • BSL Maintenance Procedures
  • 1. M00126.PDF
  • 1.1. Changing Crusher Impact Elements
  • 1.2. Confirm Safe to Start. Confirm with the section official th
  • 1.3. Electrical Isolation. Isolate and tag the Crusher, BSL and
  • 1.4. Remove Crusher Elements. Undo element bolts. Knock out ele
  • 1.5. Replace Elements. Install replacement elements and keepers.
  • 1.6. Breaking and Removing BSL Chain
  • 1.7. Confirm Safe to Start. Confirm with the section official th
  • 1.8. Position Chain. Run the chain so that a set of joining link
  • 1.9. Electrical Isolation. Isolate and tag the AFC, BSL and crus
  • 1.10. Remove tension from BSL chain.
  • 1.11. Retract the BSL tensioning cylinders. Retract the BSL tensi
  • 1.12. Engage Slow Running Device.
  • 1.13. Pull Slack Chain. Engage slow run device and run in reverse
  • 1.14. Break the Chain. Break the chain by splitting the chain joi
  • 1.15. Remove a Section of Chain. Cut a section of chain of equal
  • 1.16. Disengage Slow Runner. Disengage the slow run device.
  • 1.17. Tension BSL Chain. Extend the BSL tensioning cylinders unti
  • 1.18. Test Run the BSL. Start the BSL normally and monitor the am
  • 1.19. Checking and Changing BSL gearbox oil
  • 1.20. Check Oil Levels. Run the BSL until it is at operating temp
  • 1.21. Checking and Changing Crusher Gearbox Oil
  • 1.22. Check Oil Levels. Run the crusher until it is at operating
  • 1.23. Top Up Oil. If you want to change the oil out skip this sec
  • 1.24. Drain Oil. Place container under the drain point of the gea
  • 1.25. Fill Chambers. Check drain plug has been replaced. Pump in
  • 1.26. Changing BSL Flights
  • 1.27. Confirm Safe to Start. Confirm with the section official th
  • 1.28. Position Chain. Run the chain so that the flight to be chan
  • 1.29. Electrical Isolation. Isolate and tag the AFC and BSL as pe
  • 1.30. Remove tension from BSL chain. Open Chain Tensioning Isolat
  • 1.31. Pull Slack Chain. Run slow run in reverse to pull any slack
  • 1.32. Remove Flight Bar. Use the rattle gun to remove the flight
  • 1.33. Install New Flight Bar. Lift chain and place brace under a
  • 1.34. Disengage Slow Run Device. Disengage the Slow Run Device.
  • 1.35. Tension BSL Chain. Extend the BSL tensioning cylinders unti
  • 1.36. Test Run the BSL. Start the BSL normally and monitor the am
  • 1.37. Adjusting Pressure Reducing Valves
  • 1.37.1. Safety Instructions
  • 1.38. Confirm Safe to Start. Confirm with the section official th
  • 1.39. Adjusting Screws. The working pressure of the pressure redu
  • 1.40. Primary and Secondary Side The main valve block has two mai
  • 1.41. Increasing Pressure. In order to INCREASE the allowable inco
  • 1.42. Pressure Setting. Once the desired pressure is reached, the
  • 1.43. Confirm Safe to Start. Confirm with the section official th
  • 1.44. Adjusting Screws. In order to DECREASE the allowable outgoi
  • 1.45. This can be used to decrease the outgoing pressure set point
  • 1.46. Once the desired outgoing pressure has been reached, tighten
  • 1.47. Once the outgoing pressure (out of secondary port) has been
Rate this product

Related products