Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866
Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866 - Image 2
Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866 - Image 3
Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866 - Image 4
Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866 - Image 5

Bucyrus SKF Rotary Blasthole Drill Operation And Maintenance Manual BI615866

$30.00

  • Type Of Manual: Operation And Maintenance Manual
  • Manual ID: BI615866
  • Number of Pages: 320
  • Size: 21.5MB
  • Format: PDF
Category:

Product details

  • Model List:

    • SKF Rotary Blasthole Drill
  • 1. PARTS ORDERING AND PRODUCT SUPPORT
  • 2. Safety Information
  • 3. Safety Stand Placement
  • 4. Product Description
  • 5. SKF Component Locator
  • 6. SKFX Component Locator
  • 7. Contents
  • 8. Section 1 – Safety
  • 8.1. Hazard Classification
  • 8.2. Overview of Potential Hazards
  • 8.3. Safety Guidelines
  • 8.4. Safety Sign List
  • 8.5. Safety Sign Locator
  • 8.6. Safety Signs
  • 9. Section 2 – Operator Controls
  • 9.1. Graphic Symbol Legend
  • 9.2. Operator Control Panel (standard)
  • 9.3. Operator Control Panel (optional)
  • 9.4. Cat EMS Panel
  • 9.5. System Pressure Gauge Panel
  • 9.6. Switch Panel (standard)
  • 9.7. Lights, Circuit Breakers
  • 9.8. Heater/AC
  • 9.9. AC/Heater/Pressurizer Unit
  • 9.10. Operators Seat
  • 10. Section 3 – Lubrication and Preventative Maintenance
  • 10.1. Service PointsMainframe
  • 10.1.1. Auto Lube System
  • 10.1.2. Manual Lube System
  • 10.2. Service Points – General
  • 10.3. LubricationGeneral
  • 10.4. Lubrication and Maintenance Chart
  • 10.5. Lubricant Specifications
  • 10.5.1. Hydraulic Oil
  • 10.5.2. Compressor
  • 10.5.3. Final Drive Oil
  • 10.5.4. Lubricating Grease
  • 10.5.5. Gear Lubricant
  • 10.5.6. Engine Oil (Caterpillar)
  • 10.5.7. Engine Oil (Cummins)
  • 10.6. Extreme Weather Lubricants
  • 10.7. Preventative Maintenance
  • 10.7.1. Mast Trunnion Bolt Torque
  • 10.7.2. Charge and Loop Filters
  • 10.7.3. Hydraulic System
  • 10.7.4. Compressor Lubrication
  • 10.7.5. Cat Pump Oil Specifications
  • 10.7.6. Winch Lubrication
  • 10.7.7. Water Pump (Cat Pump)
  • 10.7.8. Cooling SystemCummins
  • 10.7.9. Cooling SystemCaterpillar
  • 10.7.10. Air Cleaners
  • 10.7.11. Mast Pivot Shaft Inspection and Repair
  • 10.7.12. Weld Inspection
  • 10.7.13. Bolted Joints
  • 10.7.14. SAE Recommended Torque Values
  • 10.7.15. Critical Fastener ID Inspection Schedule
  • 10.7.16. Electrical System
  • 10.7.17. Extended Machine Shutdown
  • 10.7.18. Scheduled Oil Sampling Analysis
  • 10.8. Drill Stem Thread Lubricator
  • 10.9. Metric Conversions
  • 10.10. Torque Values for Split Flange Connections
  • 10.11. Torque Values for Hydraulic Tubes Fittings
  • 10.12. Maintenance Record
  • 11. Section 4 – Operating Instructions
  • 11.1. Pre-Start Checks
  • 11.2. Fire Suppression System
  • 11.3. Normal Start-Up Procedure
  • 11.3.1. To Start Engine
  • 11.3.2. After Start Checks
  • 11.3.3. Normal Shut Down
  • 11.4. Ground Level Engine Stop
  • 11.5. Cold Weather Operation
  • 11.6. Propelling Machine
  • 11.7. Leveling Machine
  • 11.8. Raising Mast
  • 11.9. Lowering Mast
  • 11.10. Loading Drill Pipe
  • 11.11. Preparing to Drill
  • 11.12. Drilling Procedures
  • 11.12.1. Drilling with Standard Bit
  • 11.12.2. Drilling with a Down The Hole Hammer
  • 11.13. Multiple Pass Drilling
  • 11.13.1. Adding Drill Pipe
  • 11.13.2. Retracting Drill Pipe
  • 12. Section 5 – Drilling Practices
  • 12.1. Drilling Terminology
  • 12.2. Bit Weight Rotary Speeds
  • 12.3. Rotary Drill Bits
  • 12.4. Rotary Blast Hole Drill Strings
  • 12.5. Drill Bit Stabilizers
  • 12.6. Compressed Air
  • 12.7. Drilling Related Problems
  • 12.8. Operating Problems and Indicators
  • 12.9. Solving Drilling Problems
  • 13. Section 6 – Machine Transport and Specifications
  • 13.1. Transporting Machine
  • 13.2. Mast Removal and Installation
  • 13.3. Loading and Unloading of Machine
  • 13.4. Loading and Unloading of Mast
  • 13.5. Machine Specifications
  • 13.6. Transient Stability Limits
  • 13.7. Line of Sight Limits
  • 14. Section 7 – Options and Accessories
  • 14.1. Cold Weather Option
  • 14.2. Heater/Controller (Kim HotStart)
  • 14.3. Vigilante System
  • 14.4. Auto Lube Controller
  • 14.5. Drilling Efficiency Indicator
  • 14.6. Engine Monitor (Murphy PowerView)
  • 14.7. Shock Sub
Rate this product

Related products