Bucyrus 49-RII Diesel - Electric Blast Hole Drill Technical Manual BI616762
Bucyrus 49-RII Diesel - Electric Blast Hole Drill Technical Manual BI616762 - Image 2
Bucyrus 49-RII Diesel - Electric Blast Hole Drill Technical Manual BI616762 - Image 3
Bucyrus 49-RII Diesel - Electric Blast Hole Drill Technical Manual BI616762 - Image 4
Bucyrus 49-RII Diesel - Electric Blast Hole Drill Technical Manual BI616762 - Image 5

Bucyrus 49-RII Diesel – Electric Blast Hole Drill Technical Manual BI616762

$30.00

  • Type Of Manual: Technical Manual
  • Manual ID: BI616762
  • Number of Pages: 69
  • Size: 4.7MB
  • Format: PDF
Category:

Product details

  • Model List:

    • 49-RII Diesel – Electric Blast Hole Drill
  • 1. BI616762-00-00-EN_CMPL.pdf
  • 1.1. COVER PAGE
  • 1.2. TABLE OF CONTENTS
  • 1.3. FOREWORD
  • 1.4. SAFETY DECALS
  • 1.5. SAFETY PRECAUTIONS AND PRESTART CHECKS
  • 1.5.1. GENERAL
  • 1.5.2. SPECIFIC SAFETY RULES
  • 1.5.3. OPERATION NEAR ELECTRICAL TRANSMISSION LINES
  • 1.5.4. PRESTART CHECKS
  • 1.5.5. OUTSIDE INSPECTION
  • 1.5.6. ON-BOARD INSPECTION
  • 1.5.7. PRESTART LUBRICATION
  • 1.6. CONTROLS – LOCATION AND FUNCTION
  • 1.6.1. INTRODUCTION
  • 1.6.2. OPERATORS CONSOLE CONTROLS
  • 1.6.3. MAIN CONTROL PANEL
  • 1.6.3.1. HOIST/PULLDOWN RHEOSTAT
  • 1.6.3.2. ROTARY RHEOSTAT
  • 1.6.3.3. DRILL/PROPEL CONTROLS ON AND OFF PUSHBUTTONS
  • 1.6.3.4. HOIST/PULLDOWN SPEED SELECTOR SWITCH
  • 1.6.3.5. ROTARY SPEED SELECTOR SWITCH
  • 1.6.3.6. HOIST BRAKE SWITCH
  • 1.6.3.7. PIPE JACK SELECTOR SWITCH
  • 1.6.3.8. PIPE RACK JOYSTICK (LEFT CRAWLER PROPEL)
  • 1.6.3.9. WINCH/MAST SELECTOR SWITCH
  • 1.6.3.10. WINCH/MAST JOYSTICK (RIGHT CRAWLER PROPEL)
  • 1.6.3.11. TOOL WRENCH SWITCH
  • 1.6.3.12. DUST CURTAIN SWITCH
  • 1.6.3.13. BIT VIEW HATCH SWITCH
  • 1.6.4. PROPEL CONTROL PANEL
  • 1.6.4.1. DIESEL EMERGENCY STOP PUSHBUTTON
  • 1.6.4.2. PROPEL SPEED SELECTOR SWITCH
  • 1.6.4.3. COMPRESSOR STOP PUSHBUTTON
  • 1.6.4.4. COMPRESSOR VENT/DRILLL SWITCH
  • 1.6.4.5. HEATER/VENT/AIR CONDITIONER CONTROLS (OPTIONAL)
  • 1.6.4.6. OPERATING MODE SELECTOR SWITCH
  • 1.6.4.7. PROPEL JOYSTICKS
  • 1.6.5. SELECTOR SWITCHES PANEL
  • 1.6.5.1. BREAKOUT WRENCH SWITCH
  • 1.6.5.2. MAST BRACE LOCK SWITCH
  • 1.6.5.3. MAST LOCK SWITCH
  • 1.6.5.4. BOARDING STAIRS SWITCH
  • 1.6.5.5. ASHTRAY
  • 1.6.5.6. RADIO (OPTIONAL)
  • 1.6.6. LEVELING CONTROL PANEL
  • 1.6.6.1. MANUAL LEVELING JOYSTICKS
  • 1.6.6.2. AUTOMATIC LEVELING SWITCH
  • 1.6.6.3. WATER INJECTION ON/OFF SWITCH (OPTIONAL)
  • 1.6.6.4. WATER INJECTION FLOW CONTROL (OPTIONAL)
  • 1.6.6.5. HORN PUSHBUTTON
  • 1.6.6.6. DEPTH INDICATOR RESET PUSHBUTTON
  • 1.6.6.7. PROGRAMMED DRILL CONTROL SWITCH
  • 1.6.7. PANELVIEW MONITOR
  • 1.6.8. DIESEL GAUGES PANEL
  • 1.6.9. MACHINERY HOUSE CONTROLS
  • 1.6.9.1. CONTROLS LOCATED ON LOW VOLTAGE START CABINET
  • 1.6.9.2. CONTROLS LOCATED ON LOW VOLTAGE CABINET
  • 1.6.9.3. CONTROL LOCATED ON PROGRAMMABLE CONTROLLER CABINET
  • 1.6.9.4. CONTROLS LOCATED ON OR NEAR SCREW TYPE AIR COMPRESSOR
  • 1.6.9.5. DIESEL ENGINESTART BOX AMD EMGOME SAVER BOX
  • 1.6.9.6. LUBE CONTROL PANEL
  • 1.6.9.7. DIESEL CONTROL BOX
  • 1.6.9.8. HYDRAULIC RESERVOIR REMOTE FILL CONTROL PANEL
  • 1.7. START-UP
  • 1.7.1. INTRODUCTION
  • 1.7.2. MACHINE START-UP
  • 1.7.3. MACHINERY CHECKS
  • 1.7.4. BREAK-IN OF NEW COMPONENTS
  • 1.7.4.1. ROTARY DRIVE UNIT BREAK-IN
  • 1.7.4.2. HOIST/PULLDOWN GEARCASE BREAK-IN
  • 1.7.4.3. ELECTRIC MOTOR BREAK-IN
  • 1.8. OPERATION – GENERAL
  • 1.8.1. INTRODUCTION
  • 1.8.2. PROPELLING
  • 1.8.3. LEVELING
  • 1.8.4. MAST RAISING AND LOWERING
  • 1.8.4.1. MAST RAISING
  • 1.8.4.2. MAST LOWERING
  • 1.8.5. PULLDOWN MACHINERY OPERATION
  • 1.8.6. AUXILARY WINCH OPERATION
  • 1.8.7. PIPE RACK OPERATION
  • 1.8.8. TOOL HANDLING
  • 1.8.8.1. GENERAL OPERATING PROCEDURE
  • 1.8.8.2. PIPE LOADING AND UNLOADING
  • 1.8.8.3. DRILL TOOL STRING ASSEMBLY
  • 1.8.8.4. CASING TONG OPERATION
  • 1.8.8.5. DRILL TOOL STRING DISASSEMBLY
  • 1.8.8.6. ADDING ADDITIONAL DRILL PIPE
  • 1.8.8.7. REMOVAL OF MULTIPLE SECTION DRILL PIPE
  • 1.8.8.8. DUST SUPPRESION SYSTEM OPERATION
  • 1.9. DRILLING
  • 1.9.1. VERTICAL DRILLING
  • 1.9.1.1. GENERAL OPERATING PROCEDURES
  • 1.9.1.2. BEGINNING THE HOLE (COLLARING)
  • 1.9.1.3. NORMAL DRILLING
  • 1.9.1.4. ENDING THE HOLE (REAMING)
  • 1.9.1.5. ENDING THE HOLE (MULTIPLE PIPE SECTIONS)
  • 1.9.2. DRILLING DIFFICULT FORMATIONS
  • 1.9.2.1. UNCONSOLIDATED MATERIALS
  • 1.9.2.2. WET OR STICKY FORMATIONS
  • 1.9.3. PROGRAMMED DRILL CONTROL DRILLING
  • 1.9.3.1. PREPARING TO MOVE
  • 1.10. MACHINE SHUTDOWN
  • 1.10.1. GENERAL CONSIDERATIONS
  • 1.10.2. SHUT DOWN PROCEDURE
  • 1.10.3. SHORT TERM STORAGE
  • 1.10.4. LONG TERM STORAGE
  • 1.10.4.1. ATTENDED LONG TERM STORAGE
  • 1.10.4.2. UNATTENDED LONG TERM STORAGE
  • 1.11. APPENDIX A1 – TOOL RECOVERY
  • 1.12. APPENDIX A2 – PIPE SIZE LIMITATIONS
  • 1.13. APPENIX A3 – LUBE CHARTS
Rate this product

Related products