Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758
Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758 - Image 2
Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758 - Image 3
Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758 - Image 4
Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758 - Image 5

Bucyrus 59R Electric Blast Hole Drill Operators Manual BI616758

$30.00

  • Type Of Manual: Operators Manual
  • Manual ID: BI616758
  • Number of Pages: 83
  • Size: 5.4MB
  • Format: PDF
Category:

Product details

  • Model List:

    • 59R Electric Blast Hole Drill
  • 1. COVER PAGE
  • 2. FOREWORD
  • 3. SAFETY DECALS
  • 4. TABLE OF CONTENTS
  • 5. SAFETY PRECAUTIONS AND PRESTART CHECKS
  • 5.1. GENERAL
  • 5.2. SPECIFIC SAFETY RULES
  • 5.3. OPERATION NEAR ELECTRICAL TRANSMISSION LINES
  • 5.4. PRESTART CHECKS
  • 5.5. OUTSIDE INSPECTION
  • 5.6. ON-BOARD INSPECTION
  • 5.7. PRESTART LUBRICATION
  • 6. CONTROLS – LOCATION AND FUNCTION
  • 6.1. INTRODUCTION
  • 6.2. OPERATORS CONSOLE CONTROLS
  • 6.3. MAIN CONTROL PANEL
  • 6.3.1. HOIST/PULLDOWN RHEOSTAT
  • 6.3.2. ROTARY RHEOSTAT
  • 6.3.3. DRILL/PROPEL CONTROLS ON AND OFF PUSHBUTTONS
  • 6.3.4. HOIST/PULLDOWN SPEED SELECTOR SWITCH
  • 6.3.5. ROTARY SPEED SELECTOR SWITCH
  • 6.3.6. HOIST BRAKE SWITCH
  • 6.3.7. PIPE RACK SELECTOR SWITCH
  • 6.3.8. PIPE RACK JOYSTICK (LEFT CRAWLER PROPEL)
  • 6.3.9. WINCH/MAST SELECTOR SWITCH
  • 6.3.10. MAST/WINCH JOYSTICK (RIGHT CRAWLER PROPEL)
  • 6.3.11. TOOL WRENCH SWITCH
  • 6.3.12. DUST CURTAIN SWITCH
  • 6.3.13. BIT VIEWING HATCH SWITCH
  • 6.4. PROPEL CONTROL PANEL
  • 6.4.1. EMERGENCY STOP PUSHBUTTON (OPTIONAL)
  • 6.4.2. PROPEL SPEED SELECTOR SWITCH
  • 6.4.3. COMPRESSOR STOP PUSHBUTTON
  • 6.4.4. COMPRESSOR VENT//DRILL SWITCH
  • 6.4.5. HEATER/VENT/AIR CONDITIONER CONTROLS (OPTIONAL)
  • 6.4.6. OPERATING MODE SELECTOR SWITCH
  • 6.4.7. PROPEL JOYSTICKS
  • 6.5. SELECTOR SWITCH PANEL
  • 6.5.1. BREAKOUT WRENCH SWITCH
  • 6.5.2. PIPE POSITION SWITCH (OPTIONAL)
  • 6.5.3. DUST SEAL SWITCH (OPTIONAL)
  • 6.5.4. A-FRAME LOCK SWITCH (OPTIONAL)
  • 6.5.5. MAST BRACE LOCK SWITCH
  • 6.5.6. MAST LOCK SWITCH
  • 6.5.7. BOARDING STAIRS SWITCH
  • 6.5.8. PEDESTAL HEATER SWITCH (OPTIONAL)
  • 6.5.9. RADIO (OPTIONAL)
  • 6.6. LEVELING CONTROL PANEL
  • 6.6.1. MANUAL LEVELING JOYSTICKS
  • 6.6.2. AUTOMATIC LEVELING SWITCH
  • 6.6.3. WATER INJECTION ON/OFF SWITCH
  • 6.6.4. WATER INJECTION FLOW CONTROL (OPTIONAL)
  • 6.6.5. HORN PUSHBUTTON
  • 6.6.6. DEPTH INDICATOR RESET PUSHBUTTON
  • 6.6.7. PROGRAMMED DRILL CONTROL SWITCH
  • 6.6.8. EMERGENCY STOP PUSHBUTTON (OPTIONAL)
  • 6.6.9. PANELVIEW MONITOR
  • 6.7. MACHINERY HOUSE CONTROLS
  • 6.7.1. LIGHTENING LOAD CENTER
  • 6.7.2. CONTROLS LOCATED ON LOW VOLTAGE START CABINET
  • 6.7.3. CONTROLS LOCATED ON LOW VOLTAGE CABINET
  • 6.7.4. CONTROL LOCATED ON PROGRAMMABLE CONTROLLER CABINET
  • 6.7.5. HOIST/PULLDOWN AND ROTARY DRIVE CONTROL CABINETS
  • 6.7.6. CONTROLS LOCATED ON OR NEAR SCREW TYPE AIR COMPRESSOR
  • 6.8. MISCELLANEOUS CONTROLS
  • 6.8.1. PORTABLE REMOTE PROPEL STATION (OPTIONAL)
  • 6.8.2. LUBE CONTROL PANEL
  • 7. START-UP
  • 7.1. INTRODUCTION
  • 7.2. MACHINE START-UP
  • 7.3. MACHINERY CHECK
  • 7.4. BREAK-IN OF NEW COMPONETS
  • 7.4.1. ROTARY DRIVE UNIT BREAK-IN
  • 7.4.2. HOIST/PULLDOWN GEARCASE BREAK-IN
  • 7.4.3. ELECTRONIC MOTOR BREAK-IN
  • 8. OPERATION – GENERAL
  • 8.1. INTRODUCTION
  • 8.2. PROPELLING
  • 8.2.1. DEFINITIONS
  • 8.2.2. PROCEDURE
  • 8.3. CABLE REEL OPERATION
  • 8.4. LEVELING
  • 8.5. MAST RAISING AND LOWERING
  • 8.5.1. MAST RAISING
  • 8.5.2. MAST LOWERING
  • 8.6. PULLDOWN MACHINERY OPERATION
  • 8.7. AUXILARY WINCH OPERATION
  • 8.8. PIPE RACK OPERATION
  • 8.9. TOOL HANDLING
  • 8.9.1. GENERAL OPERATING PROCEDURE
  • 8.9.2. PIPE LOADING AND UNLOADING
  • 8.9.3. DRILL TOOL STRING ASSEMBLY
  • 8.9.4. CASING TONG OPERATION
  • 8.9.5. DRILL TOOL STRING ASSEMBLY
  • 8.9.6. ADDING ADDITIONAL DRILL PIPE
  • 8.9.7. REMOVAL OF MULTIPLE SECTION DRILL PIPE
  • 8.9.8. DUST SUPPRESSION SYSTEM OPERATION
  • 9. DRILLING
  • 9.1. VERTICAL DRILLING
  • 9.1.1. GENERAL OPERATING PROCEDURES
  • 9.1.2. BEGINNING THE HOLE (COLLARING)
  • 9.1.3. NORMAL DRILLING
  • 9.1.4. ENDING THE HOLE (REAMING)
  • 9.1.5. ENDING THE HOLE (MULTIPLE PIPE SECTIONS)
  • 9.2. DRILLING DIFFICULT FORMATIONS
  • 9.2.1. UNCONSOLIDATED MATERIALS
  • 9.2.2. WET OR STICKY FORMATIONS
  • 9.3. PROGRAMMED DRILL CONTROL DRILLING
  • 9.3.1. PREPARING TO MOVE
  • 10. MACHINE SHUTDOWN
  • 10.1. GENERAL CONSIDERATIONS
  • 10.2. SHUTDOWN PROCEDURE
  • 10.3. SHORT TERM STORAGE
  • 10.4. LONG TERM STORAGE
  • 10.4.1. ATTENDED LONG TERM STORAGE
  • 10.4.2. UNATTENDED LONG TERM STORAGE
  • 11. APPENDIX 1 – TOOL RECOVERY
  • 12. APPENDIX 2 – PIPE SIZE LIMITATIONS
  • 13. APPENDIX 3 – LUBE CHARTS
  • 14. APPENDIX 4 – OPERATORS CONSOLE (141051)
  • 15. APPENDIX 4 – OPERATORS CONSOLE (141005)
  • 16. APPENDIX 4 – OPERATORS CONSOLE (140943 AND 140967)
  • 17. APPENDIX 5 – STABILITY PROPEL (ANGLE HOLE DRILLING)
Rate this product

Related products