Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158
Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158 - Image 2
Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158 - Image 3
Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158 - Image 4
Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158 - Image 5

Bucyrus HPR6030 Hydraulic Rock Drill Technical Manual BI620158

$30.00

  • Type Of Manual: Technical Manual
  • Manual ID: BI620158
  • Number of Pages: 133
  • Size: 4.9MB
  • Format: PDF
Category:

Product details

  • Model List:

    • HPR6030 Hydraulic Rock Drill
  • 1. HPR6030 Service (431415).pdf
  • 1.1. Introduction
  • 1.2. Table of Contents
  • 1.3. Index to Figures
  • 1.4. Section 1 – Safety
  • 1.4.1. Overview of Potential Hazards
  • 1.4.2. Safety Instructions
  • 1.5. Section 2 – General Maintenance
  • 1.5.1. Operation Maintenance
  • 1.5.1.1. Start-Up Procedure
  • 1.5.1.2. Operating Tips
  • 1.5.2. General Maintenance Tips
  • 1.5.2.1. Accumulator Pressures
  • 1.5.2.2. Contamination
  • 1.5.2.3. Major Repairs
  • 1.5.3. Preventive Maintenance
  • 1.5.3.1. At the beginning of every shift
  • 1.5.3.2. Every Two Hours
  • 1.5.3.3. Every Week or Every Time the Shank is Changed
  • 1.5.3.4. Every 500 Hours or 3 Months
  • 1.6. Section 3 – Troubleshooting
  • 1.7. Section 4 – Drill Repair
  • 1.7.1. General Tips on Drill Overhaul
  • 1.7.2. Tools Required
  • 1.7.3. Seal Installation Tool
  • 1.7.4. Special Tools
  • 1.7.5. Drill Torque Specifications
  • 1.7.6. Removal of Drill from the Feed
  • 1.7.7. Installation of Drill on the Feed
  • 1.7.8. Drill Disassembly
  • 1.7.8.1. General Information
  • 1.7.8.2. Water Swivel Assembly – Removal
  • 1.7.8.3. Water Swivel Housing – Repair
  • 1.7.8.4. Rotation Motors – Removal
  • 1.7.8.5. Rotation Cover – Removal
  • 1.7.8.6. Rotation Housing – Internal Parts
  • 1.7.8.7. Chuck Driver Pinion Gears – Removal Inspection
  • 1.7.8.8. Chuck Driver Bearing Plate – Removal Inspection
  • 1.7.8.9. Thrust Washer – Inspection
  • 1.7.8.10. Cylinder – Internal Parts
  • 1.7.8.11. Cylinder – Component Parts
  • 1.7.8.12. Backhead – Removal and Inspection
  • 1.7.8.13. Hammer and Bushings – Removal and Inspection
  • 1.7.8.14. Shuttle Valve – Removal and Inspection
  • 1.7.8.15. Shuttle Valve – Internal Parts
  • 1.7.8.16. Accumulator – Internal Parts
  • 1.7.8.17. Accumulators – Removal
  • 1.7.8.18. Accumulators – Disassembly and Inspection
  • 1.7.9. Drill Assembly
  • 1.7.9.1. Cylinder – Internal Parts
  • 1.7.9.2. Rear Cylinder Bushing and Backhead – Installation
  • 1.7.9.3. Hammer – Installation
  • 1.7.9.4. Front Cylinder Bushing – Installation
  • 1.7.9.5. Accumulator – Internal Parts
  • 1.7.9.6. Accumulators – Assembly and Installation
  • 1.7.9.7. Shuttle Valve – Internal Parts
  • 1.7.9.8. Shuttle Valve – Assembly
  • 1.7.9.9. Shuttle Valve – Installation
  • 1.7.9.10. Rotation Housing – Internal Parts
  • 1.7.9.11. Rotation Housing – Assembly
  • 1.7.9.12. Chuck Driver – Assembly
  • 1.7.9.13. Rotation Motors – Installation
  • 1.7.9.14. Water Swivel – Assembly
  • 1.7.9.15. Water Swivel and Shank – Installation
  • 1.8. Section 5 – Charging the Accumulators
  • 1.8.1. Requirements
  • 1.8.2. Procedure
  • 1.8.3. Checking the Accumulator Charge Pressure
  • 1.8.4. Accumulator Charge Kit
  • 1.9. Section 6 – Specifications
  • 1.9.1. Hydraulic Oils for Percussion Drills
  • 1.9.2. Hydraulic Drill Rotation Unit Lubrication
  • 1.9.2.1. Grease Lubrication with a Hand Grease Gun
  • 1.9.2.2. Frequency
  • 1.9.2.3. Grease Specifications
  • 1.9.3. HPR6030 Wear Tolerances (60mm shank)
  • 1.9.4. Maintenance Record
Rate this product

Related products