Bucyrus Ashton DBT Shield Technical Manual BI618952
Bucyrus Ashton DBT Shield Technical Manual BI618952 - Image 2
Bucyrus Ashton DBT Shield Technical Manual BI618952 - Image 3
Bucyrus Ashton DBT Shield Technical Manual BI618952 - Image 4
Bucyrus Ashton DBT Shield Technical Manual BI618952 - Image 5

Bucyrus Ashton DBT Shield Technical Manual BI618952

$30.00

  • Type Of Manual: Technical Manual
  • Manual ID: BI618952
  • Number of Pages: 109
  • Size: 2.7MB
  • Format: PDF
Category:

Product details

  • Model List:

    • Ashton DBT Shield
  • 1. M00689.pdf
  • 1.1. General Safety
  • 1.2. Isolation Procedures
  • 1.2.1. Outbye and Monorail
  • 1.2.2. Shields
  • 1.2.2.1. Hydraulic Bleed Points
  • 1.2.2.2. Operation Screw Type
  • 1.2.2.3. Operation Manometer Gauge Port Type
  • 1.2.3. AFC and BSL
  • 1.2.4. Bootend
  • 1.2.5. Residual Risk
  • 1.2.5.1. Supplementary Regulations
  • 1.2.6. Personnel
  • 1.2.7. Operation and maintenance
  • 1.2.7.1. Qualification
  • 1.2.8. Use in conformance with specifications
  • 1.2.9. Use contrary to specifications
  • 1.2.10. Safety instructions
  • 1.2.10.1. Basic principles
  • 1.2.10.2. Prerequisite
  • 1.2.10.3. Lighting
  • 1.2.10.4. Signalling Systems and Protective Devices
  • 1.2.10.5. Emergency Stop
  • 1.2.10.6. Support Lock-out Switch
  • 1.2.10.7. Moving Parts
  • 1.2.10.8. Automatic Mode
  • 1.2.11. Storage and transport
  • 1.2.12. Installation
  • 1.2.13. Operation
  • 1.2.14. Maintenance
  • 1.2.14.1. Hydraulics
  • 1.2.14.2. Handling of Hydraulic Fluids
  • 1.2.14.3. Maintenance and Repair
  • 1.2.14.4. Whip-Checks
  • 1.2.14.5. Permissible Hoses
  • 1.2.14.6. Installation of Hydraulic Hoses
  • 1.2.15. Hosing colours
  • 1.2.16. Storage and transport
  • 1.2.17. Storage
  • 1.2.17.1. Storage of new equipment
  • 1.2.17.2. Exposure to Sunlight
  • 1.2.17.3. Natural Ageing
  • 1.2.17.4. Moisture and Dirt
  • 1.2.17.5. Short Term Storage
  • 1.2.17.6. Long Term Storage
  • 1.2.17.7. Plastic Deformation
  • 1.2.17.8. Random Sample Inspection
  • 1.2.17.9. HFA Fluids
  • 1.2.18. Used equipment
  • 1.2.18.1. Corrosion Protection
  • 1.2.19. Transport
  • 1.2.19.1. Transport Units
  • 1.2.19.2. Points of Attachment
  • 1.2.19.3. Temperatures Below Freezing
  • 1.2.19.4. Electrical and Electronic Components
  • 1.2.19.5. Transport Safety Devices and Transport Units
  • 1.3. Introduction
  • 1.3.1. General Data Information
  • 1.4. One Web Back System (OWB)
  • 1.5. Face and Gate End Shields
  • 1.6. Safe Working Areas
  • 1.6.1. Front Walkway
  • 1.7. Corrosion Protection
  • 1.7.1. Emulsion / Water / Oil Monitoring
  • 1.7.2. Quality of Processed Water
  • 1.7.3. Emulsion values
  • 1.8. Hydraulic Bleed Points
  • 1.8.1. Operation Screw Type
  • 1.8.2. Operation Manometer Gauge Port Type
  • 1.9. Control Unit Troubleshooting
  • 1.9.1. No response when selecting a function
  • 1.9.1.1. Corrective Action
  • 1.9.2. Bypassing or Sticking High or Low Flow Valves
  • 1.9.3. Replacing High/Low Flow Valve
  • 1.9.4. Double Solenoid Pilot Valve Replacement
  • 1.9.5. Control Block Filter and Pilot Non-Return Valve Replacement
  • 1.10. Cylinder Replacement
  • 1.10.1. Advancing Cylinder (DA Ram) Replacement
  • 1.10.2. Leg Cylinder Replacement
  • 1.10.3. Base Cylinder Replacement
  • 1.10.4. Stabilising Cylinder Replacement
  • 1.10.5. Side Seal Cylinder Replacement
  • 1.10.6. Anti-Topple Cylinder Replacement
  • 1.10.7. Inter-Shield Hose Replacement
  • 1.10.8. Pressure Transducers
  • 1.11. Shields Maintenance (Electrical System)
  • 1.11.1. SCU Port Assignments
  • 1.11.1.1. PMC-R Port Assignments
  • 1.11.2. SKK Cables and Power Supply Testing
  • 1.11.3. Pressure Sensor Information
  • 1.11.4. Reed Rod Information
  • 1.11.5. Faulty Sensor Indication
  • 1.11.6. PMC-R Power Adaptor
  • 1.11.7. PMC-R Isolation Coupler
  • 1.12. Shields Maintenance (Electrical) Fault Finding
  • 1.12.1. Power Group without Power
  • 1.12.2. Support Is Not Operating
  • 1.12.2.1. Possible Reason
  • 1.12.2.2. Corrective Action
  • 1.12.2.3. If no LED on the Solenoid valve operated
  • 1.12.2.4. Change the solenoid driver.
  • 1.12.3. Single SCU without Power
  • 1.12.4. No Server SCU in the Network
  • 1.12.4.1. Possible Reason
  • 1.12.4.2. Corrective Action
  • 1.12.5. Single PMC-R Reboots on Power Up
  • 1.12.6. No Hydraulic Flow Pressure
  • 1.12.7. SRB Auto Sequence Stops
  • 1.12.8. Network Drops Out During Operation
  • 1.12.9. Incomplete Network
  • 1.12.9.1. Broken cable or faulty SCU
  • 1.12.10. When Operating a Support Function, the Power Drops Off and R
  • 1.12.11. During Auto sequence Support Does not Move
  • 1.12.12. Bankpush Not Completed
Rate this product

Related products