Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 2

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 3

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 4

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 5

caterpillar general information conversion calculations and tightening torques service manual 3842952 2

caterpillar general information conversion calculations and tightening torques service manual 3842952 3

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952

$30.00

Type Of Manual: Service Manual
Manual ID: 3842952
Number of Pages: 46
Size: 0.5MB
Format: PDF

Category: Caterpillar Service Manual PDF

Model List:
- General Information, Conversion Calculations and Tightening Torques

1. Service Manual titlepage
1.1. CONTENTS
1.2. FOREWORD
1.3. SAFETY INSTRUCTIONS
1.3.1. Personnel Requirements
1.3.2. Pay attention to the hazard warnings on the machine
1.3.3. Pay attention to warnings and safety information in the manuals and instructions
1.4. SI UNITS AND OTHER UNITS OF MEASUREMENT
1.4.1. Space and mass dimensions
1.4.2. Units of time
1.4.3. Units of force, energy and power
1.5. Conversion table
1.5.1. Conversion of length dimensions
1.5.2. Conversion of area dimensions
1.5.3. Conversion of feet and inches to meters
1.5.4. Conversion of Newton meters Nm to foot pounds ft lb
1.5.5. Conversion of the pressure units for gases, vapors and fluids
1.5.6. Conversion of the units of energy, work and heat quantity
1.5.7. Conversion for the units of mechanical stress (strength)
1.5.8. Practically equivalent units for pressure and mechanical stress (strength)
1.5.9. Temperature units and conversion formulas
1.5.10. Power, energy flow, heat flow
1.5.11. Velocities
1.5.12. Units of mass (weight)
1.5.13. Units of volume, flow rate
1.5.14. Fuel consumption
1.6. CALCULATION EXAMPLES
1.6.1. Angle of inclination
1.6.2. Ground speeds
1.6.3. Hydraulic power (pumps/motors)
1.6.4. Cylinder stroke times
1.6.5. Hydraulic motor speeds
1.7. TIGHTENING TORQUES, BOLTS AND SCREWS FOR FLANGE SYSTEMS
1.7.1. General Information
1.7.2. Units of measurement
1.7.3. Identification on drawings
1.7.4. Requirements for assembly planning
1.7.5. Special requirements
1.7.6. Interpretation of torque information on separate drawings
1.7.7. Dynamic tightening torque
1.7.8. Fasten finger tight
1.7.9. Hard connections
1.7.10. Soft connections
1.7.11. Statics inspection
1.7.12. Static test torque (inspection after installation)
1.7.13. Static check procedure
1.7.14. Static test torque for 1E0279X
1.7.15. Fastening elements in hard connections
1.7.16. Fastening elements in soft connections
1.7.17. Connections
1.7.18. Static test torque for 1E0279Y
1.7.19. Dynamic tightening torques
1.7.20. Static test torques
1.7.21. Dynamic tightening torques for bolts with a diameter smaller than 6 mm
1.7.22. Static tightening torques for bolts with a diameter smaller than 6 mm
1.7.23. Straight pin assemblies, press fit pin assemblies and twelve point head bolts
1.7.24. Pin assemblies
1.7.25. Press fit pin assemblies
1.7.26. Pin assembly lubrication
1.7.27. Twelve point head bolts
1.7.28. Twelve point head bolts expansion bolts
1.7.29. Tightening torques for flange systems SAEJ518/ISO 6149/1E4217
1.7.30. Tightening angle

Rate this product