Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000
Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000 - Image 2
Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000 - Image 3
Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000 - Image 4
Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000 - Image 5

Caterpillar 72H Pipelayer Operation And Maintenance Manual WEBM1000

$30.00

  • Type Of Manual: Operation And Maintenance Manual
  • Manual ID: WEBM1000
  • Number of Pages: 232
  • Size: 6.8MB
  • Format: PDF
Category:

Product details

  • Model List:

    • 72H Pipelayer
  • 1. Literature Information
  • 2. Machine Description
  • 3. Operation
  • 4. Maintenance
  • 5. California Proposition 65 Warning
  • 6. Certified Engine Maintenance
  • 7. Machine Capacity
  • 8. Caterpillar Product Identification Number
  • 9. Safety Section (D6T LGP (OEM))
  • 9.1. Safety Messages
  • 9.2. Additional Messages
  • 9.3. General Hazard Information
  • 9.3.1. Pressurized Air and Water
  • 9.3.2. Trapped Pressure
  • 9.3.3. Fluid Penetration
  • 9.3.4. Containing Fluid Spillage
  • 9.3.5. Inhalation
  • 9.3.6. Dispose of Waste Properly
  • 9.4. Crushing Prevention and Cutting Prevention
  • 9.5. Burn Prevention
  • 9.5.1. Exhaust Gas Recirculation Cooler
  • 9.5.2. Coolant
  • 9.5.3. Batteries
  • 9.6. Fire Prevention and Explosion Prevention
  • 9.6.1. Regeneration
  • 9.6.2. General
  • 9.6.3. Battery and Battery Cables
  • 9.6.4. Lines, Tubes, and Hoses
  • 9.6.5. Fire Extinguisher
  • 9.7. Fire Safety
  • 9.8. Fire Extinguisher Location
  • 9.9. Track Information
  • 9.10. Electrical Storm Injury Prevention
  • 9.11. Before Starting Engine
  • 9.12. Engine Starting
  • 9.13. Before Operation
  • 9.14. Visibility Information
  • 9.15. Restricted Visibility
  • 9.16. Operation
  • 9.16.1. Machine Operating Temperature Range
  • 9.16.2. Machine Operation
  • 9.16.3. Limitations on Lifting Loads That Exceed the Working Range
  • 9.16.4. Electrical Power Lines
  • 9.17. Parking
  • 9.18. Slope Operation
  • 9.19. Engine Stopping
  • 9.20. Equipment Lowering with Engine Stopped
  • 9.21. Sound Information and Vibration Information
  • 9.21.1. Sound Level Information
  • 9.21.2. Sound Level Information for Machines in European Union Countries and in Countries that Adopt the
  • 9.21.3. The European Union Physical Agents (Vibration) Directive 2002/ 44/EC
  • 9.21.4. Sources
  • 9.22. Operator Station
  • 9.22.1. Rollover Protective Structure (ROPS), Falling Object Protective Structure (FOPS) or Tip Over Protection Structure (TOPS)
  • 9.22.2. Other Guards (If Equipped)
  • 10. Product Information Section (D6T LGP (OEM))
  • 10.1. Restrictions to Application and Configuration
  • 10.2. Certification
  • 10.3. ISO Symbols (Model Usage)
  • 11. Operation Section (D6T LGP (OEM))
  • 11.1. Tool Storage Area
  • 11.2. Adjusting the Seat
  • 11.3. Seat Belt Adjustment for Non- Retractable Seat Belts
  • 11.4. Seat Belt Adjustment for Retractable Seat Belts
  • 11.5. Extension of the Seat Belt
  • 11.6. Adjustable Armrests (1)
  • 11.7. Parking Brake Control (2)
  • 11.8. Differential Steering Control (3)
  • 11.9. Transmission Control (4)
  • 11.10. Service Brake Control (6)
  • 11.11. Decelerator Pedal (7)
  • 11.12. Light Switches (8, 9)
  • 11.13. Gauges and Indicators (10)
  • 11.14. Mirror (11)
  • 11.15. Speed Range Control
  • 11.16. Engine Start Switch (15)
  • 11.17. Regeneration Switch (16)
  • 11.18. Engine Fan Reverse Switch (17) (If equipped)
  • 11.19. Throttle Control Switch (18)
  • 11.20. Hydraulic Lockout Control (19)
  • 11.21. Joystick Control (20)
  • 11.22. Horn (21)
  • 11.23. Additional Operator Controls
  • 11.24. Regeneration
  • 11.25. Regeneration Indicators
  • 11.26. Regeneration Switch
  • 11.27. Soot Level Monitoring
  • 11.28. Modes of Regeneration
  • 11.29. Regeneration System Warning Indicators
  • 11.30. Key Off Regeneration
  • 11.31. Delayed Engine Shutdown
  • 11.32. Functional Test
  • 11.33. Action Lamp
  • 11.34. Status Indicators
  • 11.35. Warning Categories
  • 11.36. Monitoring System Display
  • 11.37. Performance Screens
  • 11.38. Display Module
  • 11.39. Main Menu
  • 11.40. Menu for the Operator Profile
  • 11.41. Settings Menu
  • 11.42. Service Menu
  • 11.43. Machine Status
  • 11.44. Totals Display (Menu)
  • 11.45. Electrical Connector Location
  • 11.46. Reporting a Problem
  • 11.47. Listing of Abbreviations and Terms
  • 11.48. Data Broadcasts
  • 11.49. Operation in a Blast Site
  • 11.50. Machine Security
  • 11.51. Regulatory Compliance
  • 11.52. Operating The Machine
  • 11.53. Changing Direction and Speed
  • 11.54. Checking the Battery Disconnect System
  • 11.55. Ether Starting Aid (If Equipped)
  • 11.56. Subsequent Engine Starting Procedures
  • 11.57. Delayed Engine Shut Down
  • 11.58. Idling the Engine for Extended Periods
  • 11.59. Running Engine
  • 11.60. Stopped Engine or Drive Line Defect
  • 11.61. Connection of Brake Release Pump
  • 11.62. Relief Valve Setting
  • 11.63. Connection for the Pump
  • 11.64. Brake Release
  • 11.65. Brake Engagement
  • 11.66. Use of Jump Start Cables
  • 12. Maintenance Section (D6T LGP (OEM))
  • 12.1. General Information for Lubricants
  • 12.2. Selecting the Viscosity
  • 12.3. Engine Oil
  • 12.4. Hydraulic Systems
  • 12.5. Transmission and Axles
  • 12.6. Special Applications
  • 12.7. Special Lubricants
  • 12.8. Diesel Fuel Recommendations
  • 12.9. Fuel Additives
  • 12.10. Biodiesel
  • 12.11. Coolant Information
  • 12.12. Ecology Drains
  • 12.13. Severe Environmental Factors
  • 12.14. Severe Operating Conditions
  • 12.15. Improper Maintenance Procedures (Maintenance Procedures Which May Contribute to a Severe Service Application)
  • 12.16. Maintenance Interval Schedule
  • 12.16.1. Removing the Spark Plug
  • 12.16.2. Installing the Spark Plug
  • 12.16.3. Inspect the Belt
  • 12.16.4. Functional Test of the Monitoring System Display
  • 12.16.5. Braking System (Test)
  • 12.16.6. Extended Life Coolant (ELC) Extender
  • 12.16.7. Level 1 Analysis
  • 12.16.8. Level 2 Analysis
  • 12.16.9. Primary Filter
  • 12.16.10. Secondary Filter
  • 12.16.11. Selection of the Oil Change Interval
  • 12.16.12. Procedure for Changing the Engine Oil and Filter
  • 12.16.13. SystemOne Undercarriage
  • 12.16.14. Conventional Design
  • 12.16.15. Circuit Breakers
  • 12.16.16. Lubricants
  • 12.16.17. Change the Hydraulic Oil
  • 12.16.18. Hydraulic Tank
  • 12.16.19. Steering Charge Filter
  • 12.16.20. Inspect a Used Filter for Debris
  • 12.16.21. Loose Track Adjustment
  • 12.16.22. Tight Track Adjustment
  • 12.16.23. Bolt Torque for Track Shoes
  • 12.16.24. Replace
  • 12.16.25. Drain The Oil
  • 12.16.26. Fill with Oil
  • 12.16.27. Cleaning From Ground Level
  • 13. Warranty Section (D6T LGP (OEM))
  • 14. Reference Information Section (D6T LGP (OEM))
  • 14.1. Additional Reference Material
  • 15. Safety Section (Pipelayer Attachment Kit)
  • 15.1. Safety Messages – 72H Pipelayer
  • 15.2. Before Operation
  • 15.3. Visibility Information
  • 15.4. Operation
  • 15.4.1. Machine Operating Temperature Range
  • 15.4.2. Machine Operation
  • 15.4.3. Limitations on Lifting Loads That Exceed the Working Range
  • 15.4.4. Electrical Power Lines
  • 15.5. Parking
  • 15.6. Slope Operation
  • 15.7. Equipment Lowering with Engine Stopped
  • 15.8. Sound Information and Vibration Information
  • 15.8.1. Sound Level Information
  • 15.8.2. Sound Performance for Machines that are Offered in European Union Countries and in Countries that Adopt the EU Directives
  • 15.8.3. The European Union Physical Agents (Vibration) Directive 2002/ 44/EC
  • 16. Product Information Section (Pipelayer Attachment Kit)
  • 16.1. Specifications
  • 17. Operation Section (Pipelayer Attachment Kit)
  • 17.1. Daily Checks
  • 17.2. Hydraulic Oil Temperature
  • 17.3. Speed/Lockout Control Lever (1)
  • 17.4. Speed/Lockout Control Lock (2)
  • 17.5. Hook Control (3)
  • 17.6. Accumulator – Relieving Charge
  • 17.7. Boom Control (4)
  • 17.8. Boom Stop Valve
  • 17.9. Counterweight Control (5)
  • 17.10. Counterweight Control-Lockout Lever (6)
  • 17.11. Throttle control switch Operator Heater switch (7)
  • 17.12. Horn location moved (8)
  • 17.13. Counterweight Lock Lever
  • 17.14. Equipment Lowering with Engine Stopped
  • 17.15. Shipping the Machine
  • 17.16. Removal of the Boom
  • 18. Maintenance and Lubrication Section (Pipelayer Attachment Kit)
  • 18.1. Selecting the Viscosity
  • 18.2. Capacities (Refill)
  • 18.3. S-O-S Information
  • 18.4. Maintenance Interval Schedule (MIS)
  • 18.4.1. Inspect the Hook
  • 18.4.2. Inspect Wire Cable – Boom and Hook lines
Rate this product

Related products