Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952
Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 2
Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 3
Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 4
Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952 - Image 5

Caterpillar General Information, Conversion Calculations and Tightening Torques Service Manual 3842952

$30.00

  • Type Of Manual: Service Manual
  • Manual ID: 3842952
  • Number of Pages: 46
  • Size: 0.5MB
  • Format: PDF
Category:

Product details

  • Model List:

    • General Information, Conversion Calculations and Tightening Torques
  • 1. Service Manual titlepage
  • 1.1. CONTENTS
  • 1.2. FOREWORD
  • 1.3. SAFETY INSTRUCTIONS
  • 1.3.1. Personnel Requirements
  • 1.3.2. Pay attention to the hazard warnings on the machine
  • 1.3.3. Pay attention to warnings and safety information in the manuals and instructions
  • 1.4. SI UNITS AND OTHER UNITS OF MEASUREMENT
  • 1.4.1. Space and mass dimensions
  • 1.4.2. Units of time
  • 1.4.3. Units of force, energy and power
  • 1.5. Conversion table
  • 1.5.1. Conversion of length dimensions
  • 1.5.2. Conversion of area dimensions
  • 1.5.3. Conversion of feet and inches to meters
  • 1.5.4. Conversion of Newton meters Nm to foot pounds ft lb
  • 1.5.5. Conversion of the pressure units for gases, vapors and fluids
  • 1.5.6. Conversion of the units of energy, work and heat quantity
  • 1.5.7. Conversion for the units of mechanical stress (strength)
  • 1.5.8. Practically equivalent units for pressure and mechanical stress (strength)
  • 1.5.9. Temperature units and conversion formulas
  • 1.5.10. Power, energy flow, heat flow
  • 1.5.11. Velocities
  • 1.5.12. Units of mass (weight)
  • 1.5.13. Units of volume, flow rate
  • 1.5.14. Fuel consumption
  • 1.6. CALCULATION EXAMPLES
  • 1.6.1. Angle of inclination
  • 1.6.2. Ground speeds
  • 1.6.3. Hydraulic power (pumps/motors)
  • 1.6.4. Cylinder stroke times
  • 1.6.5. Hydraulic motor speeds
  • 1.7. TIGHTENING TORQUES, BOLTS AND SCREWS FOR FLANGE SYSTEMS
  • 1.7.1. General Information
  • 1.7.2. Units of measurement
  • 1.7.3. Identification on drawings
  • 1.7.4. Requirements for assembly planning
  • 1.7.5. Special requirements
  • 1.7.6. Interpretation of torque information on separate drawings
  • 1.7.7. Dynamic tightening torque
  • 1.7.8. Fasten finger tight
  • 1.7.9. Hard connections
  • 1.7.10. Soft connections
  • 1.7.11. Statics inspection
  • 1.7.12. Static test torque (inspection after installation)
  • 1.7.13. Static check procedure
  • 1.7.14. Static test torque for 1E0279X
  • 1.7.15. Fastening elements in hard connections
  • 1.7.16. Fastening elements in soft connections
  • 1.7.17. Connections
  • 1.7.18. Static test torque for 1E0279Y
  • 1.7.19. Dynamic tightening torques
  • 1.7.20. Static test torques
  • 1.7.21. Dynamic tightening torques for bolts with a diameter smaller than 6 mm
  • 1.7.22. Static tightening torques for bolts with a diameter smaller than 6 mm
  • 1.7.23. Straight pin assemblies, press fit pin assemblies and twelve point head bolts
  • 1.7.24. Pin assemblies
  • 1.7.25. Press fit pin assemblies
  • 1.7.26. Pin assembly lubrication
  • 1.7.27. Twelve point head bolts
  • 1.7.28. Twelve point head bolts expansion bolts
  • 1.7.29. Tightening torques for flange systems SAEJ518/ISO 6149/1E4217
  • 1.7.30. Tightening angle
Rate this product

Related products